The change of surface alloy compositions and corrosion behavior after WEDM machining of commercially pure titanium (grade 4) and Ti-6Al-4V (grade 5)
คำสำคัญ:
Corrosion, Diffusion, WEDM, Titanium, Ti-6Al-4Vบทคัดย่อ
Nowadays, titanium and its alloys are widely used in medical applications because of excellent corrosion resistance and a high strength-to-weight ratio. Nevertheless, titanium and its alloys are classified as difficult-to-machine metals by conventional machining methods. Therefore, unconventional machining processes are recommended. Wire-electrical discharge machining (WEDM) has become an important non-traditional machining process, as it provides an effective solution for machining components made from difficult-to-machine metals. However, WEDM could damage the surface layer and have an effect on the biocompatibility properties. This research was focused on the effect of WEDM on grade 4 commercially pure titanium and Ti-6Al-4V (Grade 5) after WEDM cutting. The diffusion of wire substance was studied, and corrosion behavior in Hank’s solution was examined. The experimental result showed that the depth of damaged layer on WEDMed specimens was around 5-12 μm, and the surface compositional analysis showed a very limited depth of contamination from wire electrode. The corrosion rate of the WEDMed specimens are 300 - 400 higher than the rate found in the as-received specimens.
Downloads
เอกสารอ้างอิง
Brunette, D.M., Tengvall, P., Textor, M. & Thomsen, P. (2001). Titanium in medicine: Material Science, Surface Science, Engineering, Biological. Springer: 674-772.
Bronzino, J.D. (2006). Biomedical engineering fundamentals. (3rd ed.). New York, NY: CRC.
Guሷçluሷ, F.M., Çimenoǧlu, H. & Kayali, E.S. (2006). The recrystallization and thermal oxidation behavior of CP-titanium. Mat. Sci. Eng. C-Bio. S. 26(8): 1367-1372.
Brewer, W.D., Bird, R.K. & Wallace, T.A. (1998). Titanium alloys and processing for high speed aircraft. Mat. Sci. Eng. A-Struct. 243(1-2): 299-304.
Kuriakose, S. & Shunmugam, M.S. (2004). Characteristics of wire-electro discharge machined Ti6Al4V surface. Mater. Lett. 58(17-18): 2231-2237.
Ho, K.H., Newman, S.T., Rahimifard, S. & Allen, R.D. (2004). State of the art in wire electrical discharge machining (WEDM). Int. J. Mach. Tool. Manu. 44(12-13):1247-1259.
Puri, A.B. & Bhattacharyya, B. (2003). An analysis and optimisation of the geometrical inaccuracy due to wire lag phenomenon in WEDM. Int. J. Mach. Tool. Manu. 43(2): 151-159.
Shobert, E.I. (1983). What happens in EDM. In: E.C. Jameson (Ed.). Electrical discharge machining: tooling, methods and applications. Michigan, MI: Society of Manufacturing Engineers: 3-4.
Tsai, H.C., Yan, B.H. & Huang, F.Y. (2003). EDM performance of Cr/Cu-based composite electrodes, Int. J. Mach. Tool. Manu. 43(3): 245-252.
Boothroyd, G. & Winston, A.K. (1989). Nonconventional machining processes. In: Fundamentals of machining and machine tools. New York, NY: Marcel Dekker: 491.
McGeough, J.A. (1988). Electro discharge machining. In: Advanced methods of machining. London: Chapman & Hall: 130.
Huang, C.A., Hsu, F.Y. & Yao, S.J. (2004). Microstructure analysis of the martensitic stainless steel surface fine-cut by the wire electrode discharge machining (WEDM). Mat. Sci. Eng. A-Struct. 371(1-2): 119-126.
Wang, P.W., Hsu, J.C. & Hwa, L.G. (2008). Metallic phase formation in oxide films. J. Non-Cryst. Solids 354(12-13): 1256-1262.
Blasco-Tamarit, E., Igual-Muñoz, A., García Antón, J. & García-García, D. (1961). Corrosion behaviour and galvanic coupling of titanium and welded titanium in LiBr solutions. Oxford: Elsevier Science.
Fraker, A.C. (2005). Corrosion test and standards (2nd ed.). U.S.A.: 834-845.
ASTM Standard(2007). Section 3; Materials test method and analytical procedures. Vol. 03.01; Metals - Mechanical Testing; Elevated and Low-Temperature Tests; Metallography.
Manna, A. & Bhattacharyya, B. (2006). Taguchi and Gauss elimination method: A dual response approach for parametric optimization of CNC wire cut EDM of PRAlSiCMMC. Int. J. Adv. Manuf. Technol. 28(1-2): 67-75.
Tai, T.Y. & Lu, S.J. (2009). Improving the fatigue life of electro-discharge machined SDK11 tool steel via the suppression of surface cracks. Int. J. Fatigue 31(3): 433-438.
Lee, S.H. & Li, X. (2003). Study of the surface integrity of the machined workpiece in the EDM of tungsten carbide, J. Mater. Process. Tech. 139(1-3): 315-321.
Poorqasemi, E., Abootalebi, O., Peikari, M., Haqdar, F. (2009). Investigating accuracy of the Tafel extrapolation method in HCl solutions. Corros. Sci. 51(5): 1043- 1054.
Ntasi, A, Mueller, WD, Eliades, G. & Zinelis, S. (2010). The effect of eletro discharge machining (EDM) on the corrosion resistance of dental alloys. Dent Mater. 26(12): 237-245.
ดาวน์โหลด
เผยแพร่แล้ว
วิธีการอ้างอิง
ฉบับ
บท
การอนุญาต
ลิขสิทธิ์ (c) 2017 วารสารโลหะ, วัสดุ และแร่
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Authors who publish in this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
