Effect of sintering on microstructure and properties of hydroxyapatite produced by different synthesizing methods
คำสำคัญ:
Hydroxyapatite, Microstructures, Mechanical properties, Bioceramicsบทคัดย่อ
The aim of this study is to investigate the effect of the sintering schedule on microstructure and properties of hydroxyapatite which is produced by different synthesizing methods. Hence, wet-chemical precipitation and solid-state reaction were performed to prepare nano-sized hydroxyapatite (HA) powders. Powders were then uniaxially pressed and sintered by varying temperatures and times. XRD and SEM were used to identify phases and morphology. Density and porosity of the sintered sample were determined using the Archimedes technique. Flexural strength was measured by a universal testing machine. The results show that density and strength could be improved by increasing the sintering temperature in both HAW and HAD. However, with increasing sintering temperatures, average grain sizes of HAW and HAD samples were not significantly increased. The sintering temperature seems to play a more important role than sintering time in the densification process of hydroxyapatite. In addition, the thermal stability in sintered HAD samples induced a weaker flexural strength of samples in comparison with HAW. Therefore, the optimized microstructure and properties of sintered hydroxyapatite can be prepared by using the suitable synthesizing method together with the workable sintering schedule for each synthesizing process.Downloads
เอกสารอ้างอิง
Hench, L.L. (1991). Bioceramics: from concept to clinic. J. Am. Ceram. Soc. 74: 1487-1510.
LeGeros, R.Z. & Legeros, J.P. (1993). Dense hydroxyapatite. In : L.L. Hench & J. Willson (eds.). An introduction to bioceramics. London: World Scientific: pp. 139-180.
Tracy, B.M. & Doremus, R.H. (1984). Direct electron microscopy studies of the bonehydroxyapatite interface. J. Biomed. Mater. Res. 18(7) : 719-726.
Jarcho, M., Bolen,C.H., Thomas, M.B., Bobick, J., Kay, J.F. & Doremus, K.H. (1976). Hydroxyapatite synthesis and characterization in dense polycrystalline form. J. Mater. Sci. 11: 2027-2035.
Liu, C., Huang, Y., Shen, W. & Cui, J. (2001). Kinetics of hydroxyapatite precipitation at pH 10 to 11. Biomaterials 22(4) : 301-306.
Santos, M.H., de Oliveira, M., de Freitas Zouza, L.P., Mansur, H.S. & Vasconcelos, W.L. (2004). Synthesis control and characterization of hydroxyapatite prepared by wet precipitation process. Mater. Res. 7(4) : 625-630.
Zhang, S. & Gonsalves, K.E. (1997). Preparation and characterization of thermally stable nanohydroxyapatite. J. Mater. Sci.: Mater. Med. 8(1) : 25-28.
Afshar, A., Ghorbani, M., Ehsani, N., Saeri, M.R. & Sorrel, C.C. (2003). Some important factors in the wet precipitation process of hydroxyapatite. Mater. Design. 24(3) : 197-202.
García, C., Paucer, C., Gaviria, J. & Duran, A. (2005). Effect of some physical-chemical variables in the synthesis of hydroxyapatite by the precipitation route. Key Eng. Mater. 284-286: 47-50.
Arita, I.H., Castano, V.M. & Wilkinson, D.S. (1995). Synthesis and processing of hydroxyapatite ceramic tapes with controlled porosity. J. Mater. Sci.: Mater. Med. 6(1) : 19-23.
Kim, W., Zhang, Q. & Saito, F. (2000). Mechanochemical synthesis of hydroxyapatite from Ca(OH)2-P2O5 and CaO-Ca(OH)2-P2O5 mixtures. J. Mater. Sci. 35(21) : 5401-5405.
Zhang, X. & Vecchio, K.S. (2007). Hydrothermal synthesis of hydroxyapatite rods. J. Cryt. Growth. 308(1) : 133-140.
Zhu, R., Yu, R., Yao, J., Wang, D. & Ke, J. (2008). Morphology control of hydroxyapatite through hydrothermal process. J. Alloy Comp. 457(1-2): 555-559.
Kothapalli, C., Wei, M., Vasiliev, A. & Shaw, M.T. (2004). Influence of temperature and concentration on the sintering behavior and mechanical properties of hydroxyapatite. Acta Materialia. 52(19) : 5655-5663.
Webster, T.J., Ergun, C., Doremus, R.H., Siegel, R.W. & Bizios, R. (2001). Enhanced osteoclast-like cell functions on nano-phase ceramics. Biomaterials. 22(11) : 1327-1333.
Cao, L.Y., Zhang, C.B. & Huang, J.F. (2005). Synthesis of hydroxyapatite nanoparticles in ultrasonic precipitation. Ceram. Int. 31(8): 1041-1044.
Kong, L.B., Ma, J. & Boey, F. (2002). Nanosized hydroxyapatite powders derived from coprecipitation process. J. Mater. Sci. 37(6) : 1131-1134.
Akao, M., Aoki, H. & Kato, K. (1981). Mechanical properties of sintered hydroxyapatite for prosthetic applications. J. Mater. Sci. 16(3) : 809-812.
Martin, R.I. & Brown, P.W. (1995). Mechanical properties of hydroxyapatite formed at physiological temperature. J. Mater. Sci.: Mater. Med. 6(3) : 138-143.
Somiya, S. (1989). Advanced technical ceramics. California : Academic press: pp. 230-231.
Rodriguez-Lorenzo, L.M., Vallet-Regi, M. & Ferreira, J.M.F. (2001). Colloidal processing of hydroxyapatite. Biomaterials. 22(13) : 1847-1852.
Wang, C.K., Ju, C.P. & Lin, J.H.C. (1998). Effect of doped bioactive glass on structure and properties of sintered hydroxyapatite. Mater. Chem. Phys. 53(2) : 138-149.
Sadeghian, Z., Heinrich, J.G. & Moztarzadeh, F. (2006). Influence of powder pre-treatments and milling on dispersion ability of aqueous hydroxyapatite-based suspensions. Ceram. Int. 32(3) : 331-337.
Sung, Y.M., Lee, J.C. & Yang, J.W. (2004). Crystallization and sintering characteristics of chemically precipitated hydroxyapatite nanopowder. J. Cryt. Growth. 262(1-4) : 467-472.
Royer, A., Viguie, J.C., Heughebaert, M. & Heughebaert, J.C. (1993). Stoichiometry of hydroxyapatite: Influence on the flexural strength. J. Mater. Sci.: Mater. Med. 4(1) : 76-82.
Wang, P.E. & Chaki, T.K. (1993). Sintering behavior and mechanical properties of hydroxyapatites and dicalcium phosphate. J. Mater. Sci.: Mater. Med. 4(2) : 150-158.
Liu, D.M. (1997). Influence of porosity and pore size on the compressive strength of porous hydroxyapatite ceramic. Ceram. Int. 23(2) : 135-139.
Rodríguez-Lorenzo, L.M., Vallet-Regí, M. & Ferreira, J.M.F. (2001). Fabrication of hydroxyapatite bodies by uniaxial pressing from a precipitated powder. Biomaterials. 22(6) : 583-588.
ดาวน์โหลด
เผยแพร่แล้ว
วิธีการอ้างอิง
ฉบับ
บท
การอนุญาต
ลิขสิทธิ์ (c) 2017 Journal of Metals, Materials and Minerals
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Authors who publish in this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
