Prediction of tensile strength for sandwich injection molded short-glass-fiber reinforced thermoplastics
คำสำคัญ:
sandwich injection molding, short-fiber reinforced composites, tensile strength, fiber orientation distribution, fiber length distributionบทคัดย่อ
This present paper provides a modified rule-of-mixtures relationship which allows for the calculation of ultimate tensile strength (UTS) as a function of the area fraction between skin and core layers.The effects of fiber length and fiber orientation within the skin and core layers on the tensile strength of conventional and sandwich injection molded short-glass-fiber reinforced polypropylene have been studied in detail. The present theory is then applied to existing experimental results and the agreement is found to be satisfactory.Downloads
เอกสารอ้างอิง
Bailey, R.S. 1994. Conventional thermoplastics. In : Handbook of Polymer-Fiber Composites, Polymer Science and Technology Series. New York : Longman Scientific & Technical.
Clegg, D.W. 1994. Recycling of polymer composites. In : Handbook of PolymerFiber Composites, Polymer Science and Technology Series. New York : Longman Scientific & Technical.
Singh, P. and Kamal, M.R. 1989. The effect of processing variables on microstructure of injection molded short-fiber reinforced polypropylene composites. Polym. Compos. 10(5) : 344-351.
Gupta, V. B., Mittal, R. K., Sharma, P. K., Mennig, G. and Wolters, J. 1989. Some studies on glass-fiber-reinforced polypropylene; Part I : reduction in fiber length during processing. Polym.Compos. 10(1) : 8-15.
Tancrez, J-P., Pabiot, J. and Rietsch, F. 1996. Damage and fracture mechanisms in thermoplastic-matrix composites in relation to processing and structural parameters. Compos. Sci. Technol. 56 : 725-731.
Barbosa, S.E. and Kenny, J.M. 1999. Analysis of the relationship between processing conditions-fiber orientation-final properties in short-fiber reinforced polypropylene. J. Reinf. Plast. Compos. 18(5) : 413-420.
Akay, M. and Barkley, D. 1985. Processingstructure-property interaction in injection molded glass-fiber-reinforced polypropylene. Compos. Struct. 3 : 269-293.
Gupta, V.B., Mittal, R.K., Scharma, P K., Mennig, G. and Wolters, J. 1989. Some studies on glass-fiber-reinforced polypropylene; Part II: mechanical properties and their dependence on fiber length, interfacial adhesion, and fiber dispersion. Polym. Compos. 10(1) : 16-27.
Franzen, B., Klason, C., Kubat, J. and Kitano, T. 1989. Fiber degradation during processing of short-fiber reinforced thermoplastics, Composites. 20(1) : 65-76.
Akay, M. and Barkley, D. 1991. Fiber orientation and mechanical behavior in reinforced thermoplastic injection moldings. J. Mater. Sci. 26(10) : 2731-2742.
Chin-Ping, Fung, Hwang, J.R. and Hsu, C.C. 2003. The effect of injection molding process parameters on the tensile properties of short-glass-fiber reinforced PBT. Polym.-Plast. Technol. Eng. 41(1) : 45-63.
Halpin, J.C. and Kardos, J.L. (1978). Strength of discontinuous reinforced composites: Fiber reinforced composites. Polym. Eng. Sci. 18(6) : 496-504.
Kardos, J.L. and Halpin, J.C. 1999. Short predicting the strength and toughness of fiber composites. Macromol. Symp. 147 : 139-153.
Xia, M., Hamada, H. and Maekawa, Z. 1995. Flexural stiffness of injection molded glass fiber reinforced thermoplastics. Int. Polym. Process. 10(1) : 74-81.
Fukuda, H. and Chou, T.W. 1982. A probabilitistic theory of the strength of short-fiber composites with variable fiber length and orientation. J. Mater. Sci. 17(4) : 1003-1011.
Templeton, P.A. (1990). Strength predictions of injection molding compounds. J. Reinf. Plast. Compos. 9(3) : 210-225.
Fu, S.Y. and Lauke, B. 1996. Effects of fiber length and fiber orientation distributions on the tensile strength of short-fiber reinforced polymers. Compos. Sci. Technol. 56(10) : 1179-1190.
Fu, S.Y. and Lauke, B. 1998. The elastic modulus of misaligned short-fiber reinforced polymers. Compos. Sci. Technol. 58(3-4) : 389-400.
Van Hattum, F.W.J. and Bernardo, C.A. 1999. A model to predict the strength of shortfiber composites. Polym. Compos. 20(4) : 524-533.
Thomason, J.L. 2002. Micromechanical parameters from macromechanical measurements on glass reinforced polypropylene. Compos. Sci. Technol. 62(10-11) : 1455-1468.
Bay, R.S. and Tucker, C.L. III 1992. Fiber orientation in simple injection molding, Part 1: Theory and numerical methods. Polym. Compos. 13(4) : 332-341.
Patcharaphun, S. and Mennig, G. 2005. Properties enhancement of short-glass-fiber reinforced thermoplastics via sandwich injection molding. Polym. Compos. 26(6) : 823-831.
Denault, J., Vu-Khanh, T. and Foster, B. 1989. Tensile properties of injection molded long fiber thermoplastic composites. Polym. Compos. 10(5) : 313-321.
Miles, I.S. and Rostami, S. 1992. Multicomponent Polymer Systems, Polymer Science and Technology Sires. New York : Longman Scientific & Technical.
Lee, S. M. 1992 . Handbook of Composite Reinforcements. New York : VCH Publishers. 153.
ดาวน์โหลด
เผยแพร่แล้ว
วิธีการอ้างอิง
ฉบับ
บท
การอนุญาต
ลิขสิทธิ์ (c) 2017 Journal of Metals, Materials and Minerals
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Authors who publish in this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
