Structural integrity assessment of tufted textile composite and its comparison with laminated textile composite

ผู้แต่ง

  • Abbasali Saboktakin Department of Mechanical Engineering, University of Sistan and Baluchestan https://orcid.org/0000-0002-1825-0097
  • Amir Ghasemi Department of Mechanical Engineering, University of Sistan and Baluchestan
  • Hossein Mohammadi Department of Mechanical Engineering, University of Sistan and Baluchestan

คำสำคัญ:

Tufted composite, Static test, Fatigue test, Damage characterization

บทคัดย่อ

Three dimensional composites have been used in aerospace industry to improve interlaminar strength. This paper evaluates the 3D tufted composites from aspect of their mechanical properties. The tufted composite panel was manufactured based on polyester resin as well as an untufted laminated composite for comparison purposes. Experiments show that specimens with transverse tufting suffer slighter reduction in the tensile strength than longitudinal tufting. The tufted composites are found lower tensile strength compared with laminated composite samples accompanied with slight improvement in the compression strength and high strain rate tensile strength. The experimental results presented in this paper should be valuable to achieve desired property of tufted composites for specific aerospace applications.

Downloads

Download data is not yet available.

ประวัติผู้แต่ง

Abbasali Saboktakin, Department of Mechanical Engineering, University of Sistan and Baluchestan

Abbasali Saboktakin, PhD

Assistant Professor

Department of Mechanical Engineering

University of Sistan and Baluchestan

 Zahedan, Iran

เอกสารอ้างอิง

T. Uozumi and T. Yamamoto, "CFRP using braided preforms/RTM process for aircraft applications," Advanced Composite Materials, vol. 14, pp. 365-383, 2005.

M. Dow and H. Dexter, "Development of stitched, braided and woven composite structures in the ACT Program and at Langley Research Center," N. TP-97- 206234, Editor. 1997.

C. Poe, H. Dexter, and I. Raju, "A review of the nasa textile composites research," American Institute of Aeronautics and Astronautics, 1997.

N. Naouar, E. Vidal-Salle, J. Schneider, E. Maire, and P. Boisse, "3D composite reinforcement meso FE analyses based on Xray computed tomography," Journal Composite Structures, vol. 132, pp.1094- 1104, 2015.

L. Tong, 3D fibre reinforced polymer composites. London: Elsevier Science Ltd, 2002.

D. Benjamin, S. Oyadiji, and P. Potluri, "Characterising mechanical properties of braided and woven textile composite beams," Applied Composite Materials, vol. 16, pp. 15–31, 2009.

A. P. Mouritz, "A mechanistic approach to the properties of stitched laminates," Composites: Part A. vol.3, pp. 1–27, 2000.

A. Byun, "Impact properties of laminated composites with stitching fibers," Composite Structures, vol. 76, pp. 21–27, 2008.

A. Mouritz and N. Cox, "A mechanistic approach to the properties of stitched laminates," Composites Part A, vol.3, pp. 1- 27, 2000.

G. Dell'Anno, D. Cartié, I. Partridg, and A. Rezai, "Exploring mechanical property balance in tufted carbon fabric/epoxy composites," Composites Part A, vol.38, pp. 2366-2373, 2007.

R. Francois, "Compaction of textile reinforcements for composites manufacturing. I: Review of experimental results," Polymer Composites, vol.19, pp. 198-216, 2014.

M. Colin de Verdiere, A. A. Skordos, M. May, and A. C. Waltond, "Influence of loading rate on the delamination response of untufted and tufted carbon epoxy non crimp fabric composites: Mode I," Engineering Fracture Mechanics, vol. 96, pp. 11-25, 2012.

M. Colin de Verdiere, A. K. Pickett, A. A. Skordos, and V. Witzel, "Evaluation of the mechanical and damage behaviour of tufted non crimped fabric composites using full field measurements," Composites Science and Technology, vol. 69, pp. 131-138, 2009.

V. Koissin, S. Lomov, and I. Verpoest, "Structurally stitched preforms: Experimental characterization, geometrical modelling, and FE analysis," European Conference on Composite Materials (ECCM- 13), Stockholm, 2008.

R. Tomek, "Mixed mode fracture toughness of stitched laminated composites." Master Thesis, University of florida, 2004.

M. N. Saleh and C. Soutis, "Recent advancements in mechanical characterisation of 3D woven composites," Mechanics of Advanced Materials and Modern Processes, vol. 2017, pp. 1-17, 2017.

S. Choi and H. Shyprykevich, "Damage development in notched composite laminates under compression-dominated fatigue," Composites Science and Technology, vol.62, pp. 851-860, 2002.

J. Tate and A. Kelkar, "Stiffness degradation model for biaxial braided composites under fatigue loading," Composite Part B, vol.39, pp. 548–555, 2008.

ดาวน์โหลด

เผยแพร่แล้ว

2019-03-29

วิธีการอ้างอิง

[1]
A. . Saboktakin, A. Ghasemi, และ H. Mohammadi, “Structural integrity assessment of tufted textile composite and its comparison with laminated textile composite”, J Met Mater Miner, ปี 29, ฉบับที่ 1, มี.ค. 2019.

ฉบับ

ปีที่ 29 ฉบับที่ 1 (2019)

บท

Original Research Articles

การอนุญาต

ลิขสิทธิ์ (c) 2019 Journal of Metals, Materials and Minerals

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Authors who publish in this journal agree to the following terms:

    1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.

 

    1. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.