Effect of powder mixture conditions on mechanical properties of sintered Al<sub>2</sub>O<sub>3</sub>-SS 316L composites under vacuum atmosphere

Authors

  • Ruangdaj Tongsri National Metals and Materials Technology Center (MTEC), Pathumthani
  • Seksak Asavavisithchai Department of Metallurgical Engineering, Faculty of Engineering Chulalongkorn University
  • Chanchai Mateepithukdharm Department of Metallurgical Engineering, Faculty of Engineering Chulalongkorn University
  • Thummasin Piyarattanatrai Department of Metallurgical Engineering, Faculty of Engineering Chulalongkorn University
  • Panyawat Wangyao Metallurgy and Materials Science Research Institute (MMRI), Chulalongkorn University

Keywords:

metal-matrix composites, SS 316L, Al2O3 particles

Abstract

Al2O3-SS 316L composites belong to new generation materials which should be characterized by a specified combination of properties. This study is concerned with the effect of the preparation method of the starting mixed powders upon the properties of Al2O3-SS 316L composites sintered under vacuum atmosphere. The composites were produced using powder mixtures with various weight shares between Al2O3 and SS 316L as well as varying size of Al2O3 particles. The mixtures were prepared by a conventional mechanical mixing. It was found that the addition of Al2O3 particles resulted in a slight decrease in the sintering density, the ultimate tensile strength and elongation, but a slight increase in the hardness. A decrease in the strength was attributed to poor sintering between 316L and Al2O3 particles, poor distribution of very fine Al2O3 particles in the composites as well as a high amount of voids and/or porosities after sintering.

Downloads

Download data is not yet available.

References

Chmielewski, M., Pietrzak, K. and Wlosinski, W. 2006. Properties of Sintered Al2O3-Cr Composites Depending on the Method of Preparation of the Powder Mixture. Sci. Sint. 38 : 231-238

Yotkeaw, T., Krataitong, R., Morakotjinda, M., Daraphan, A., Tosangthum, N. and Coovattanachai, O. 2006. Reinforcement of P/M 316L by Al2O3 Particles, Thailand Materials Science and Technology Conference. : 181-183.

Mima, S., Yotkeaw, T., Morakotjinda, M., Tosangthum, N., Daraphan, A., Krataitong, R., Coovattanachai, O., Vetayanugul, B. and Tongsri, R. 2006. Carbide-Reinforced 316L Composites, Thailand Materials Science and Technology Conference. : 178-180.

Stewenson, R. W. 1984. P/M Stainless Steels.In : Metals Handbook. 9th ed. (V.7 Powder Melallurgy). Metals Park, OH : ASM : 728-732.

Sanderow, H. I. 1990. Stainless Steel P/M AlloysUnique Applications, High Temperature Sintering. New Jersey, Metal Powder Industries Federation : 39-54.

Upadhyaya, G. S. 2000. Sintered Metallic and Ceramic Materials: Preparation, Properties and Applications. Chichester, U.K. John Wiley & Sons : 189-191.

Abenojar, J., Velasco, F., Bautista, A., Campos, M., Bas, J. A. and Torralba, J. M. 2003. Atmosphere Influence in Sintering Process of Stainless Steels Matrix Composites Reinforced with Hard Particles. Comp. Sci. Tech. 63(1) : 69-79.

Jain, J., Kar, A. M. and Upadhyaya, A. 2004. Effect of YAG Addition on Sintering of P/M 316L and 434L Stainless Steels. Mater. Lett. 58 : 2037-2040.

Pagounis, E. and Lindroos, V. K. 1998. Processing and Properties of Particulate Reinforced Steel Matrix Composites. Mater. Sci. Eng. A246 : 221-234.

Kaczmar, J. and Niechajowicz, A. 1998. Ores and Non-ferrous Metals. 33 : 418.

Downloads

Published

2017-04-23

How to Cite

[1]
R. Tongsri, S. Asavavisithchai, C. Mateepithukdharm, T. Piyarattanatrai, and P. Wangyao, “Effect of powder mixture conditions on mechanical properties of sintered Al<sub>2</sub>O<sub>3</sub>-SS 316L composites under vacuum atmosphere”, J Met Mater Miner, vol. 17, no. 1, Apr. 2017.

Issue

Vol. 17 No. 1 (2007)

Section

Original Research Articles

License

Copyright (c) 2017 Journal of Metals, Materials and Minerals

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Authors who publish in this journal agree to the following terms:

    1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.

 

    1. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.

Most read articles by the same author(s)

<< < 1 2 3 4 > >>