Processing of nano fillers in nitrile rubber – A novel technique

ผู้แต่ง

  • V.K. Abitha Department of Polymer Science and Rubber Technology, Cochin University of Science and Technology
  • Ajay Vasudeo RANE entre for Green Technology, Department of Polymer and Surface Engineering and Technology, Institute of Chemical Technology
  • K. Rajkumar Indian Rubbers Manufacturers Research Association, Thane, Maharashtra

คำสำคัญ:

Nano-TiO2, Nano Silica, NBR, Liquid NBR, Morphology, Mechanical properties, Microstructure characterization

บทคัดย่อ

Dispersion of various nano fillers like Nano silica, nano clay, Nano TiO2, etc has been attempted in NBR rubbers using new technique of dispersion. Liquid NBR is taken as dispersion media for nano fillers in polymer matrix and polymer nano composites were characterized by Rubber Process Analyzer [RPA-2000, USA].  The dispersion of the nano fillers were investigated by XRD, SEM-EDS. The effect of increasing nano- fillers on mechanical properties like tensile strength, modulus and Elongation at break was studied. Hot air ageing of polymer nano composites was also studied. Dispersion of various nano fillers like Nano silica, nano clay, Nano TiO2, etc has been attempted in NBR rubbers using new technique of dispersion. Liquid NBR is taken as dispersion media for nano fillers in polymer matrix and polymer nano composites were characterized by Rubber Process Analyzer [RPA-2000, USA].  The dispersion of the nano fillers were investigated by XRD, SEM-EDS. The effect of increasing nano- fillers on mechanical properties like tensile strength, modulus and Elongation at break was studied. Hot air ageing of polymer nano composites was also studied. 

Downloads

Download data is not yet available.

ประวัติผู้แต่ง

Ajay Vasudeo RANE, entre for Green Technology, Department of Polymer and Surface Engineering and Technology, Institute of Chemical Technology

Centre for Green Technology, M.Tech Green Technology

เอกสารอ้างอิง

Novak, B.M. (1993). Hybrid nanocomposite materials-between inorganic glasses and organic polymers. Adv. Mater. 5(6) : 422-433.

Mark, J. E. (1996). Ceramic-reinforced polymers and polymer-modified ceramics. Polym. Eng. Sci. 36(24) : 2905-2920.

Vollath, D. and Szabó, D.V. (2004). Synthesis and Properties of Nanocomposites. Adv. Eng. Mater. 6(3) : 117-127.

Messersmith, P.B. and Giannelis, E.P. (1993). Polymer-layered silicate nanocomposites: in situ intercalative polymerization of epsilon-caprolactone in layered silicates. Chem. Mater. 5(8) : 1064-1066.

Giannelis, E.P. (1996). Polymer layered silicate nanocomposites. Adv. Mater. 8(1) : 29-35.

Zilg, C., Thomann, R., Finter, J. and Mulhaupt, R. (2000). The influence of silicate modification and compatibilizers on mechanical properties and morphology of anhydride-cured epoxy nanocomposites. Macromol. Mater. Eng. 280 : 41-46.

Ray, S.S. and Okamoto, M. (2003). Polymer/layered silicate nanocomposites : a review from preparation to processing. Prog. Polym. Sci. 28(11) : 1539-1641.

Usuki, A., Hasegawa, N. and Kato, M. (2005). Polymer-clay nanocomposites. Adv. Polym. Sci. 179 : 135-195.

Wu, Y.P., Wang, Y.Q., Zhang, H.F., Wang, Y.Z., Yu, D.S., Zhang, L.Q. and Yang, J. (2005). Rubber-pristine clay nanocomposites prepared by co-coagulating rubber latex and clay aqueous suspension. Compos. Sci. Technol. 65(7-8) : 1195-1202.

Ajayan, P. M. and Zhou, O. Z. (2001). Applications of carbon nanotubes. Topics in Appl. Phys. 80 : 391-425.

Dai, L.M. and Mau, A.W.H. (2001). Controlled synthesis and modification of carbon nanotubes and C-60 : Carbonnanostructures for advanced polymer composite materials. Adv. Mater. 13 : 899-913.

Coleman, J. N., Khan, U. and Gun’ko, Y. K. (2006). Mechanical reinforcement of polymers using carbon nanotubes. Adv. Mater. 18 : 689-706.

Rajkumar, K., Kumari, N., Ranjith, P., Chakraborty, S. K., Thavamani, P., Pazhanisamy, P. and Jeyanthi, P. (2011). High temperature resistance properties of NBR based polymer nanocomposites. Int. J. Chem. Tech. Res. 3(3) : 1343-1348.

ดาวน์โหลด

เผยแพร่แล้ว

2015-12-30

วิธีการอ้างอิง

[1]
V. Abitha, A. V. RANE, และ K. Rajkumar, “Processing of nano fillers in nitrile rubber – A novel technique”, J Met Mater Miner, ปี 25, ฉบับที่ 2, ธ.ค. 2015.

ฉบับ

ปีที่ 25 ฉบับที่ 2 (2015)

บท

Original Research Articles

การอนุญาต

ลิขสิทธิ์ (c) 2016 วารสารโลหะ, วัสดุ และแร่

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Authors who publish in this journal agree to the following terms:

    1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.

 

    1. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.