The effects of double intercritical annealing on microstructure and mechanical properties of 0.107C-2.39Mn-0.453Si dual phase steel

Nithi SAENARJHAN; Gobboon LOTHONGKUM; Jatupon OPAPAIBOON

doi:10.55713/jmmm.v32i4.1537

ผู้แต่ง

Nithi SAENARJHAN Department of Metallurgical Engineering, Faculty of Engineering, Chulalongkorn University, Bangkok, 10330, Thailand
Gobboon LOTHONGKUM Department of Metallurgical Engineering, Faculty of Engineering, Chulalongkorn University, Bangkok, 10330, Thailand
Jatupon OPAPAIBOON Department of Metallurgical Engineering, Faculty of Engineering, Chulalongkorn University, Bangkok, 10330, Thailand

DOI:

https://doi.org/10.55713/jmmm.v32i4.1537

บทคัดย่อ

In this study, double intercritical annealing was applied to modify the mechanical properties of 0.107%C-2.39%Mn-0.453%Si dual phase steel. The effects of the double intercritical annealing (DIA) method were investigated via microstructure observation and tensile test, and then compared with the single intercritical annealing (SIA) method. By increasing the intercritical annealing temperature, yield and tensile strengths increase while ductility decreases primarily due to the increase of martensite fraction. DIA leads to a slight reduction of the ferrite size and the martensite fraction regardless of the intercritical annealing temperature. Tensile results showed that DIA increases ductility without losing significant amount of strength. The outcome implies that the DIA method can be used to modify the mechanical properties of DP steels without adding excessive complexity to the process.

Downloads

Download data is not yet available.

เอกสารอ้างอิง

H. Yu, Y. Guo, and X. Lai, “Rate-dependent behavior and constitutive model of DP600 steel at strain rate from 10-4 to 103s-1,” Materials & Design, vol. 30, no. 7, pp. 2501-2505, 2009.

S. Curtze, V.T. Kuokkala, M. Hokka, and P. Peura, “Deformation behavior of TRIP and DP steels in tension at different temperatures over a wide range of strain rates,” Materials Science and Engineering: A, vol. 507, no. 1-2, pp. 124-131, 2009.

O. Bouaziz, H. Zurob, and M. Huang, “Driving force and logic of development of advanced high strength steels for automotive applications,” Steel Research International, vol. 84, no. 10, pp. 937-947, 2013.

H. Hofmann, D. Mattissen, and T.W. Schaumann, “Advanced cold rolled steels for automotive applications,” Steel Research International, vol. 80, no. 1, pp. 22-28, 2009.

S. Nikkhah, H. Mirzadeh, and M. Zamani, “Fine tuning the mechanical properties of dual phase steel via thermomechanical processing of cold rolling and intercritical annealing,” Materials Chemistry Physics, vol. 230, pp. 1-8, 2019.

P. Movahed, S. Kolahgar, S.P.H. Marashi, M. Pouranvari, and N. Parvin, “The effect of intercritical heat treatment temperature on the tensile properties and work hardening behavior of ferrite–martensite dual phase steel sheets,” Materials Science and Engineering: A, vol. 518, no. 1-2, pp. 1-6, 2009.

R. O. Rocha, T. M. F. Melo, E. V. Pereloma, and D. B. Santos, “Microstructural evolution at the initial stages of continuous annealing of cold rolled dual-phase steel,” Materials Science and Engineering: A, vol. 391, no. 1-2 pp. 296-304, 2005.

N. Nakada, Y. Arakawa, K.S. Park, T. Tsuchiyama, and S. Takaki, “Dual phase structure formed by partial reversion of cold-deformed martensite,” Materials Science and Engineering: A, vol. 553, pp. 128-133, 2012.

K. S. Park, M. Nishiyama, N. Nakada, T. Tsuchiyama, and S. Takaki, “Effect of the martensite distribution on the strain hardening and ductile fracture behaviors in dual-phase steel,” Materials Science and Engineering: A, vol. 604, pp. 135-141, 2014.

K. S. Park, K. T. Park, D. L. Lee, and C. S. Lee, “Effect of heat treatment path on the cold formability of drawn dual-phase steels,” Materials Science and Engineering: A, vol. 449-451, pp. 1135-1138, 2007.

J. Dai, Q. Meng, and H. Zheng, “High-strength dual-phase steel produced through fast-heating annealing method,” Results in Materials, vol. 5, p. 100069, 2020.

N. Saeidi, F. Ashrafizadeh, and B. Niroumand, “Development of a new ultrafine grained dual phase steel and examination of the effect of grain size on tensile deformation behavior,” Materials Science and Engineering: A, vol. 599, pp. 145-149, 2014.

H. Ashrafi, M. Shamanian, R. Emadi, and N. Saeidi, “A novel and simple technique for development of dual phase steels with excellent ductility,” Materials Science and Engineering: A, vol. 680, pp. 197-202, 2017.

M. Balbi, I. Alvarez-Armas, and A. Armas, “Effect of holding time at an intercritical temperature on the microstructure and tensile properties of a ferrite-martensite dual phase steel,” Materials Science and Engineering: A, vol. 733, pp. 1-8, 2018.

A. K. Srivastava, N. K. Patel, B. R. Kumar, A. Sharma, and B. Ahn, “Strength–ductility trade-off in dual-phase steel tailored via controlled phase transformation,” Journal of Materials Engineering and Performance, vol. 29, no. 5, pp. 2783-2791, 2020.

S. Ghaemifar, and H. Mirzadeh, “Enhanced mechanical properties of dual-phase steel by repetitive intercritical annealing,” Canadian Metallurgical Quarterly, vol. 56, no. 4, pp. 459-463, 2017.

S. Ghaemifar, H. Mirzadeh, M. S. Khorrami, R. Soltani, and Z. Nasiri, “Improved properties of dual-phase steel via pre-intercritical annealing treatment and thermal cycling,” Materials Science and Technology, vol. 36, no. 15, pp. 1663-1670, 2020.

S. Ghaemifar, and H. Mirzadeh, “refinement of banded structure via thermal cycling and its effects on mechanical properties of dual phase steel,” Steel Research International, vol. 89, no. 6, p. 1700531, 2018.

A. A. Gorni, Steel Forming and Heat Treating Handbook, são vicente, 2012.

C. Peng-Heng, and A.G. Preban, “The effect of ferrite grain size and martensite volume fraction on the tensile properties of dual phase steel,” Acta Metallurgica, vol. 33, no. 5, pp. 897-903, 1985.

B. Gao, X. Chen, Z. Pan, J. Li, Y. Ma, Y. Cao, M. Liu, Q. Lai, L. Xiao, and H. Zhou, “A high-strength heterogeneous structural dual-phase steel,” Journal of Materials Science, vol. 54, no. 19, pp. 12898-12910, 2019.

M. Soleimani, H. Mirzadeh, and C. Dehghanian, “Unraveling the effect of martensite volume fraction on the mechanical and corrosion properties of low-carbon dual-phase steel,” Steel Research International, vol. 91, no. 2, p. 1900327, 2020.

A. H. Jahanara, Y. Mazaheri, and M.Sheikhi, “Correlation of ferrite and martensite micromechanical behavior with mechanical properties of ultrafine grained dual phase steels,” Materials Science and Engineering: A, vol. 764, p. 138206, 2019.

C. Tian, D. Ponge, L. Christiansen, and C. Kirchlechner, “On the mechanical heterogeneity in dual phase steel grades: Activation of slip systems and deformation of martensite in DP800,” Acta Materialia, vol. 183, pp 274-284, 2020.