Production and characterization of SiC reinforced aluminum alloy matrix composites from waste beverages cans
DOI:
https://doi.org/10.55713/jmmm.v29i4.535คำสำคัญ:
Sic, Waste, Aluminum, Stir Casting, Composite, Microstructureบทคัดย่อ
In the study; SiC reinforced (1-12 wt. %) aluminum matrix composites from waste beverage cans were fabricated by stir casting method. The effect of reinforcement ratio on the experimental density, hardness, the compressive and tensile strength of the composites was investigated. The crystal structures and microstructure of the composite materials were analyzed by X-ray diffraction (XRD) method and scanning electron microscopy (SEM). From the results, the hardness of composites increased from 70,81 HV (pure Al alloy) to 89,80 HV (for 9 wt. % SiC). The compressive and tensile strengths were performed as 763,69 MPa (for 5 wt. % SiC) and 201,79 MPa (for 1 wt. % SiC) compared with pure aluminum alloy (620,35 MPa and 154,71 MPa).Downloads
เอกสารอ้างอิง
P. B. Pawar and A. A. Utpat, “Development of Aluminium Based Silicon Carbide Particulate Metal Matrix Composite for Spur Gear,” Procedia Materials Science, vol. 6, pp. 1150- 1156, 2014. DOI: https://doi.org/10.1016/j.mspro.2014.07.187
N. S. V. Balajia and M. M. Hussainc, “Manufacture of Aluminium Metal Matrix Composite (Al7075-SiC) by Stir Casting Technique,” Materials Today: Proceedings, vol. 2, pp. 3403-3408, 2015. DOI: https://doi.org/10.1016/j.matpr.2015.07.315
H. Mindivan, “Investigation of tribological behaviour of silicon carbide reinforced aluminum matrix composites,” Master Thesis, Institute of Science and Technology, Technical University, 2007.
P. Bajaj, “Mechanical behaviour of aluminium based metal matrix composites reinforced with SiC and alumina,” Master, Mechanical Engineering, Thapar University, 2007.
M. T. Sijo and K. R. Jayadevan, “Analysis of stir cast aluminum silicon carbide metal matrix composite: A comprehensive review,” Procedia Technology, vol. 24, pp. 379-385, 2016. DOI: https://doi.org/10.1016/j.protcy.2016.05.052
C. M. Şenel, M. Gürbüz, and E. Koç, “New generation composites with graphene reinforced aluminum matrix,” Engineer and Machine, vol. 56, p. 669, 2015.
L. L. J. Hashim and M. S. J. Hashmi, “Metal matrix composites: production by the stir casting method,” Journal of Materials Processing Technology, vol. 92-93, pp. 1-7, 1999. DOI: https://doi.org/10.1016/S0924-0136(99)00118-1
M. Gürbüz, “Effect of the cold working on mechanical properties of aluminum produced from waste beverage cans,” Journal of Science and Engineering, vol. 20, no. 58, pp. 28-35, 2018.
J. Hindi, U. Achutha Kini, S. S. Sharma, B. M. Gurumurthy, and M. C. G. Shankar, “Mechanical characterization of stir cast Al 6063 matrix SiC reinforced metal matrix compositesi,” the 5th International Conference on Automotive, Mechanical and Materials Engineering (ICAMME' 2015) Bali, Indonesia, 2015, pp. 69-73.
P. Saenpong, S. Talangkul, T. Laonapakul, and A. Boonma, “Microstructures and hardness of A356-SiC composites produced by the mechanical stir casting,” Materials Today: Proceedings vol. 5, no. 3, pp. 9489-9496, 2018. DOI: https://doi.org/10.1016/j.matpr.2017.10.129
R. Kumar and V. Kumar, “Experimental analysis of mechanical properties of aluminium alloy with silicon carbide,” International Journal of Mechanical Engineering and Technology, vol. 8, no. 12, pp. 99-107, 2017.
M. H. Rahman and H. M. M. A. Rashed, “Characterization of silicon carbide reinforced aluminum matrix composites,” Procedia Engineering, vol. 90, pp. 103-109, 2014. DOI: https://doi.org/10.1016/j.proeng.2014.11.821
M. Singla, D. D. Dwivedi, L. Singh, and V. Chawla, “Development of Aluminium Based Silicon Carbide Particulate Metal Matrix Composite,” Journal of Minerals & Materials Characterization & Engineering, vol. 8, no. 6, pp. 455-467, 2009. DOI: https://doi.org/10.4236/jmmce.2009.86040
Z. O. D. Sujan, M. E. Rahman, M. A. Maleque and C. K. Tan, “Physio-mechanical Properties of Aluminium Metal Matrix Composites Reinforced with Al2O3 and SiC,” International Scholarly and Scientific Research & Innovation vol. 6, no. 8, pp. 678-681, 2012.
M. C. Şenel, M. Gürbüz, and E. Koç, “Mechanical and tribological behaviours of aluminium matrix composites reinforced by graphene nanoplatelets,” Materials Science and Technology, vol. 34, pp. 1980-1989, 2018. DOI: https://doi.org/10.1080/02670836.2018.1501839
H. J. Ryu, S. I. Cha, and S. H. Hong, “Generalized shear-lag model for load transfer in SiC/Al metal-matrix composites,” Materials Research Society, vol. 18, no. 12, pp. 2851- 2858, 2003. DOI: https://doi.org/10.1557/JMR.2003.0398
M. Rashad, Fusheng, Zhang, J. and Asif M. , “Use of high energy ball milling to study the role of graphene nanoplatelets and carbon nanotubes reinforced magnesium alloy,” Journal of Alloys and Compounds, vol. 646, pp. 223-232, 2015. DOI: https://doi.org/10.1016/j.jallcom.2015.06.051
ดาวน์โหลด
เผยแพร่แล้ว
วิธีการอ้างอิง
ฉบับ
บท
การอนุญาต
ลิขสิทธิ์ (c) 2019 Journal of Metals, Materials and Minerals
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Authors who publish in this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
