Utilization of RHA in development of hybrid composite by electromagnetic stir casting technique using RSM
DOI:
https://doi.org/10.55713/jmmm.v29i4.538คำสำคัญ:
RHA, B4C CCD, desirability, electromagnetic stirringบทคัดย่อ
In the present investigation, hybrid metal matrix composite was developed using electromagnetic stir casting technique. AA2024 alloy was used as matrix material. RHA (rice husk ash) was used as primary reinforcement material, while B4C (boron carbide) was used as secondary reinforcement material. CCD (central composite design) was employed to develop design matrix table for fabrication of hybrid composite by electromagnetic stir casting technique. Microstructure result showed uniform distribution of RHA and B4C in matrix material. Ramp function graph showed that when RHA preheat temperature, RHA weight percentage, Electromagnetic stirring time, B4C preheat temperature and B4C wt.% are 272.57°C, 12.5%, 180 s, 312.38°C and 12.5% respectively then the optimum value of tensile strength of composite was found to be 258.498 MPa with desirability 0.958. Hardness, toughness and ductility were also observed at optimum electromagnetic stir casting parameters.Downloads
เอกสารอ้างอิง
A. Ahmadi, M. R. Toroghinejad, and A. Najafizadeh, “Evaluation of Microstructure and Mechanical Properties of Al/Al2O3/SiC Hybrid Composite Fabricated by Accumulative Roll Bonding Process,” Materials & Design, vol. 53, pp. 13-19, 2014. DOI: https://doi.org/10.1016/j.matdes.2013.06.064
A. Devaraju, A. Kumar, A. Kumaraswamy, and B. Kotiveerachari, “Influence of Reinforcements (SiC and Al2O3) and Rotational Speed on Wear and Mechanical Properties of Aluminum Alloy 6061-T6 based Surface Hybrid Composites Produced via Friction Stir Processing,” Materials&Design, vol. 51, pp. 331-341, 2013. DOI: https://doi.org/10.1016/j.matdes.2013.04.029
P. K. Rohatgi, J. K. Kim, N. Gupta, Simon Alaraj, and A. Daoud, “Compressive Characteristics of A356/Fly Ash Cenosphere Composites Synthesized by Pressure Infiltration Technique,” Composites: Part A, vol. 37, pp. 430-437, 2006. DOI: https://doi.org/10.1016/j.compositesa.2005.05.047
N. Verma and S. C. Vettivel, “Characterization and experimental analysis of boron carbide and rice husk ash reinforced AA7075 aluminium alloy hybrid composite,” Journal of Alloys and Compounds, vol. 741, pp. 981-998, 2018. DOI: https://doi.org/10.1016/j.jallcom.2018.01.185
J. A. Kingsly Gladston, N. Mohamedsheriff, I. Dinaharan, and J. D. Selvam, “Production and characterization of rich husk ash particulate reinforced AA6061 aluminum alloy composites by compocasting,” Transactions of Nonferrous Metals Society of China, vol. 25, pp. 683-691, 2015. DOI: https://doi.org/10.1016/S1003-6326(15)63653-6
Casting Routes,” Composites Science and Technology, Vol. 67, pp.3369-3377, 2007. DOI: https://doi.org/10.1016/j.compscitech.2007.03.028
R. Rahmani Fard and F. Akhlaghi, “Effect of Extrusion Temperature on the Microstructure and Porosity of A356-Sicp Composites,” Journal of Materials Processing Technology, vol. 187-188, pp. 433-436, 2007. DOI: https://doi.org/10.1016/j.jmatprotec.2006.11.077
K. Sudarshan and M. K. Surappa, “Dry Sliding Wear of Fly Ash Particle Reinforced A356 Al Composites,” Wear, vol. 265, pp. 349-360, 2008. DOI: https://doi.org/10.1016/j.wear.2007.11.009
A. Cetin and A. Kalkanli, “Effect of Solidification Rate on Spatial Distribution of SiC Particles in A356 Alloy Composites,” Journal of Materials Processing and Technology, vol. 205, pp. 1-8, 2008. DOI: https://doi.org/10.1016/j.jmatprotec.2007.11.065
M. K. Naskar, D. Kundu, and M. Chatterjee, “Coral-like hydroxy sodalite particles from rice husk ash as silica source.” Materials Letters, vol. 65, pp. 3408-3410, 2011. DOI: https://doi.org/10.1016/j.matlet.2011.07.084
R. Khan, A. Jabbar, I. Ahmad, W. Khan, A. N. Khan, and J. Mirza, “Reduction in environmental problems using rice-husk ash in concrete”, Construction and Building Materials, vol. 30, pp. 360-365, 2012. DOI: https://doi.org/10.1016/j.conbuildmat.2011.11.028
S. P. Dwivedi and V. R. Mishra, “Physicochemical, Mechanical and Thermal Behaviour of Agro Waste RHA Reinforced Green Emerging Composite Material”, Arabian Journal for Science and Engineering, 2019, DOI: https://doi.org/10.1007/s13369-019-03784-z. DOI: https://doi.org/10.1007/s13369-019-03784-z
S. S. Rehman, W. Ji, S. A. Khan, M. Asif, Z. Fu, W. Wang, H. Wang, J. Zhang, and Y. Wang, “Microstructure and mechanical properties of B4C based ceramics with Fe3Al as sintering aid by spark plasma sintering”, Journal of the European Ceramic Society, vol. 34, pp. 2169- 2175, 2014. DOI: https://doi.org/10.1016/j.jeurceramsoc.2014.02.014
M. S. Heydari, H. R. Baharvandi, and S. R. Allahkaram, “Electroless nickel-boron coating on B4C-Nano TiB2 composite powders”, International Journal of Refractory Metals and Hard Materials, vol. 76, pp. 58-71, 2018. DOI: https://doi.org/10.1016/j.ijrmhm.2018.05.012
N. N. Greenwood and A. Earnshaw, “Chemistry of the Elements (2nd ed.)”, Butterworth-Heinemann. p. 149, 1997, ISBN 978-0-08-037941-8.
P. Mukerjee, “Crop Burning: Punjab and Haryana’s killer fields,” 2016, https://www. downtoearth.org.in/news/air/crop-burning-punjabharyana-s-killer-fields-55960
ดาวน์โหลด
เผยแพร่แล้ว
วิธีการอ้างอิง
ฉบับ
บท
การอนุญาต
ลิขสิทธิ์ (c) 2019 Journal of Metals, Materials and Minerals
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Authors who publish in this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
