The microgeometry parameters of uncoated and zinc-coated cold rolled steel strips

ผู้แต่ง

  • Jana Bidulská Department of Metal Forming, Faculty of Metallurgy, Technical University Košice
  • Tibor Kvačkaj Department of Metal Forming, Faculty of Metallurgy, Technical University Košice
  • Vladimír Bodák Research and Testing Institute, U. S. Steel Košice, s.r.o.
  • Róbert Bidulskỳ Institute of Materials Research, SAS Košice

คำสำคัญ:

cold working, microgeometry parameters, texturingt, surface roughness, peak coun

บทคัดย่อ

The microgeometry of surface is arithmetically expressed by the arithmetical mean deviation of the profile, Ra and peak count, Pc. Roughening of working rolls was achieved by using the technology EDT (Electric Discharge Texturing) and SBT (Shot Blast Texturing). The paper shows the relationship between the basic microgeometry parameters and the adjustment technology of working rolls. Zinc-coated cold rolled steel strips, uncoated cold rolled steel strips and the Ra, Pc parameters were measured using the tangent profilometer “Hommel Tester T1000â€. Measurements of Ra and Pc showed the scatter for SBT and EDT rolls, respectively. EDT can provide a considerably greater degree of control of surface texture than SBT together with an accurate selection of surface roughness, Ra, and peak count, Pc. The peak count obtained can be appreciably higher than that obtained with shot blasting. In comparison with SBT, it is considered that the operating costs associated with EDT are lower.

Downloads

Download data is not yet available.

เอกสารอ้างอิง

El-Menshawy, M.F. and Snaith, B. 1991. Advances in electro-discharge texturing (EDT) for cold mill work rolls. Iron Steel Eng. 68 : 57 – 59.

Aspinwall, D.K., Zhao, F. L. and El-Menshawy, M. F. 1989. Electrodischarge texturing of steel rolls. Surf. Topography. 2 : 123-141.

Bidulska, J., Kvackaj, T., Bodak, V. and Bidulsky, R. 2002. Creation of microgeometry cold rolling strip of material ST 15. Acta Metall. Slovaca. 8 : 145-150

Pankert, R. 1990. Work roll roughening in cold mills. Stahl und Eisen. 110 : 55-60.

Thomas, T. R. 1999. Rough surfaces. 2nd ed. New York : Imperial College Press.

Larena, A., Millan, F., Verdu, M. and Pinto, G. 2001. Surface roughness characterisation of multilayer polymer films for graphic arts applications. Appl. Surf. Sci. 174 : 217- 224.

Barica, S. and Bodák, V. 1998. Analysis of contemporaneous possibilities of work rolls surface preparation for sheets cold rolling. Hutnícke Listy. 53 : 22 - 26.

Simao, J., Aspinwall, D. K., Wise, M.L.H. and El-Menshawy, M. F. 1994. Mill roll texturing using EDT. J. Mater. Process. Technol. 45 : 207–214.

Simao, J. D., Aspinwall, K., Wise, M.L.H. and El-Menshawy, M. F. 1996. Electrical discharge texturing of cold mill work rolls using different tool electrode materials. Iron Steel Eng. 73 : 42 – 47.

Carless, P. 1985. Use of "high chrome" irons as roll materials for cold rolling applications. Conference on Advanced in cold Rolling Technology. London, 17-19. September, 1985 : 168 – 172.

Jonasson, M., Pulkkinen, T., Gunnarsson, L. and Schedin, E. 1997. Comparative study of shotblasted and electrical-dischargetextured rolls with regard to frictional behavior of the rolled steel sheet surfaces. Wear. 207 : 34–40.

Bastawros, A. F. and Speer, J. G. 1992. A procedure to determine surface waviness. In: Proc. 34th Mechanical Working and Steel Processing Conference. Montreal, Canada, 1992. 30 : 485-489.

Vermeulen, M. 1994. Proc. of 6th International Conference on Metrology and Properties of Engineering Surfaces. University of Birmingham, UK, April 6-8, 1994.

Kuwamoto, H., Kawano, M., Koga, Y., Kachi, Y. and Hiasa, M. 1985. Development of a new roll texturing system: electric discharge method. In: Conference on Advanced in cold Rolling Technology. London, 17-19. September 1985 : 108-114.

Kellock, B. 1988. Laser-EDM challenge to shot-blast texturing. Mach. Product. Eng. 146 : 26-27.

ดาวน์โหลด

เผยแพร่แล้ว

2017-04-23

วิธีการอ้างอิง

[1]
J. . Bidulská, T. Kvačkaj, V. Bodák, และ R. Bidulskỳ, “The microgeometry parameters of uncoated and zinc-coated cold rolled steel strips”, J Met Mater Miner, ปี 17, ฉบับที่ 2, เม.ย. 2017.

ฉบับ

ปีที่ 17 ฉบับที่ 2 (2007)

บท

Original Research Articles

การอนุญาต

ลิขสิทธิ์ (c) 2017 Journal of Metals, Materials and Minerals

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Authors who publish in this journal agree to the following terms:

    1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.

 

    1. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.