Effect of pure titanium particle size on density, hardness, wear resistance and microstructure properties

ผู้แต่ง

  • Tugba Mutuk Department of Metallurgical and Materials Engineering, Ondokuz Mayıs University
  • Mevlüt Gürbüz Department of Mechanical Engineering, Ondokuz Mayıs University

คำสำคัญ:

Titanium, Particle size, Hardness, Wear resistance, Microstructure

บทคัดย่อ

In this study, pure titanium particle samples with different particle sizes were produced by powder metallurgy method. In the sample production, pure titanium particles having a different particle size of ≤30µm, ≤43µm, ≤150µm were used. Titanium (Ti) samples were sintered at 1100°C for 120 min. Density, hardness, wear resistance and microstructure analyzes were performed on the Titanium samples. According to the results, the best mechanical properties values were obtained with ≤30 µm particle size of Titanium. The best density and hardness results are 4.28 g·cm-3 and 419.8 HV, respectively. The results of the wear rate were found under 30 N load of 8.21×10-5 mm3·Nm. Mass loss results were measured as 5.2 mg (under load of 30 N). SEM analyses showed that a good bonding and strong neck formation between the particles were observed for particle size of ≤30 µm.

Downloads

Download data is not yet available.

เอกสารอ้างอิง

K. S. Munir, Y. Zheng, D. Zhang, J. Lin, Y. Li, and C. Wen, “Microstructure and mechanical properties of carbon nanotubes reinforced titanium matrix composites fabricated via spark plasma sintering,” Materials Science and Engineering: A, vol. 688, pp. 505-523, 2017.

A. Molinari, G. Straffelini, B. Tesi, and T. Bacci, “Dry sliding wear mechanisms of the Ti6Al4V alloy,” Wear, vol. 208, pp. 105-112, 1997.

H. Dong and T. Bell, “Enhanced wear resistance of titanium surfaces by a new thermal oxidation treatment,” Wear, vol. 238, pp. 131-137, 2000.

ASM Metals Handbook, 9. ed. (Properties and Selection: Stainless Steels, Tool Materials and Species-Purpose Metals Titanium and Titanium Alloys). pp. 352.

ASM Metals Handbook, 8. ed. (Properties and Selection: Metals, Stainless Steels, Titanium and Titanium Alloys, no. 1.). pp. 1147.

K. Tanrıöven and A. Taşçı, “Titanyum Alaşımlarının Isıl İşlemi,” Makine Magazin, pp. 58, 1997.

I. Y. Kim, B. J. Choi, Y. J. Kim, and Y. Z. Lee, “Friction and wear behavior of titanium matrix (TiB+TiC) composites,” Wear, vol. 271, no. 9- 10, pp. 1962-1965, 2011.

D. E. Alman and J. A. Hawk, “The abrasive wear of sintered titanium matrix–ceramic particle reinforced composites,” Wear, vol. 225- 229, pp. 629-639, 1999.

M. Gürbüz and T. Mutuk, "Effect of process parameters on hardness and microstructure of graphene reinforced titanium composites,” Journal of Composite Materials, vol. 52, no. 4, pp. 543-551, 2017.

Z. Zaiyu and L. Yilong, “Fabrication of Titanium Metallic Composites Reinforced with Graphene Nanosheets,” in International Conference on Architectural Engineering and New Materials, 2017.

J. Liu, M. Wu, Y. Yang, G. Yang, H. Yan, and K. Jiang, “Preparation and mechanical performance of graphene platelet reinforced titanium nanocomposites for high temperature applications,” Journal of Alloys and Compounds, vol. 765, pp. 1111-1118, 2018.

W. D. Callister and D. G. Rethwisch, Materials Science and Engineering. 2015.

M. Can Şenel, M. Gürbüz, and E. Koç, “Grafen Takviyeli Alüminyum Esaslı Kompozitlerin Mekanik Özellikleri ve Aşınma Davranışının İncelenmesi,” presented at the 1st International Symposium on Multidisciplinary Studies and Innovative Technologies Proceedings, Tokat, Türkiye, 2017.

ดาวน์โหลด

เผยแพร่แล้ว

2019-09-30

วิธีการอ้างอิง

[1]
T. Mutuk และ M. Gürbüz, “Effect of pure titanium particle size on density, hardness, wear resistance and microstructure properties”, J Met Mater Miner, ปี 29, ฉบับที่ 3, ก.ย. 2019.

ฉบับ

ปีที่ 29 ฉบับที่ 3 (2019)

บท

Original Research Articles

การอนุญาต

ลิขสิทธิ์ (c) 2019 Journal of Metals, Materials and Minerals

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Authors who publish in this journal agree to the following terms:

    1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.

 

    1. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.