Comparative study of frictional behavior of Cr-doped and Al:Ti-doped DLC coatings on AISI 4140 steel
DOI:
https://doi.org/10.55713/jmmm.v37i1.2688Keywords:
Diamond-like carbon, Tribology, Wear, Ball-on-flat, SteelAbstract
Diamond-like carbon (DLC) coatings have attracted significant interest for applications requiring low friction and high surface durability. Consequently, various DLC formulations have been developed to meet different tribological demands. In this study, the frictional behavior of AISI 4140 carbon steel, which is a widely used high strength structural material, was investigated following surface modification with two distinct DLC coating configurations. Specifically, Cr‒doped DLC with a graded CrCN interlayer (Cr‒DLC/CrCN) and AlTi-doped DLC with a graded AlTiCN interlayer (Al:Ti‒DLC/AlTiCN) were compared. Wear tests were performed using the ball-on-flat method. The results show that the Cr‒DLC/ CrCN coating exhibited a lower coefficient of friction (0.26) than the Al:Ti‒DLC/AlTiCN coating (0.30). Laser scanning confocal microscopy also revealed a smaller wear track on the Cr‒DLC/CrCN surface, with a reduced depth (2.52 µm) and width (496.68 µm). Raman spectroscopy indicated a higher sp2 bonding fraction in the Cr‒DLC/CrCN coating, as reflected by its increased ID/IG ratio, which contributed to its lower friction behavior. Overall, the Cr‒DLC/CrCN coating demonstrated superior tribological performance and wear resistance, making it a more promising surface modification for enhancing the durability of AISI 4140 carbon steel in severe sliding wear environments, typical in oil and gas industries.
Downloads
References
A. H. Meysami, R. Ghasemzadeh, S. H. Seyedein, and M. R. Aboutalebi, “An investigation on the microstructure and mechanical properties of direct-quenched and tempered AISI 4140 steel,” Materials & Design, vol. 31, no. 3, pp. 1570–1575, 2010. DOI: https://doi.org/10.1016/j.matdes.2009.09.040
B. Podgornik, J. Vizintin, O. Wänstrand, M. Larsson, S. Hogmark, H. Ronkainen, and K. Holmberg, “Tribological properties of plasma nitrided and hard coated AISI 4140 steel,” Wear, vol. 249, no. 3–4, pp. 254–259, 2001. DOI: https://doi.org/10.1016/S0043-1648(01)00564-6
P. Wongpanya, P. Silawong, and P. Photongkam, “Adhesion and corrosion of Al–N doped diamond-like carbon films synthesized by filtered cathodic vacuum arc deposition,” Ceramics International, vol. 48, no. 14, pp. 20743–20759, 2022. DOI: https://doi.org/10.1016/j.ceramint.2022.04.055
P. Wongpanya, N. Pintitraratibodee, K. Thumanu, and C. Euaruksakul, “Improvement of corrosion resistance and bio-compatibility of 316L stainless steel for joint replacement application by Ti-doped and Ti-interlayered DLC films,” Surface and Coatings Technology, vol. 425, 2021. DOI: https://doi.org/10.1016/j.surfcoat.2021.127734
C. Wei, and J. Y. Yen, “Effect of film thickness and interlayer on the adhesion strength of diamond like carbon films on different substrates,” Diamond and Related Materials, vol. 16, no. 4‒7, pp. 1325–1330, 2007. DOI: https://doi.org/10.1016/j.diamond.2007.02.003
W. G. Cui, Q. B. Lai, L. Zhang, and F. M. Wang, “Quantitative measurements of sp3 content in DLC films with Raman spectro-scopy,” Surface and Coatings Technology, vol. 205, no. 7, pp. 1995–1999, 2010. DOI: https://doi.org/10.1016/j.surfcoat.2010.08.093
J. A. Santiago, I. Fernández-Martínez, J. C. Sánchez-López, T. C. Rojas, A. Wennberg, V. Bellido-González, J. M. Molina-Aldareguia, M. A. Monclús, and R. González-Arrabal, “Tribo-mechanical properties of hard Cr-doped DLC coatings deposited by low-frequency HiPIMS,” Surface and Coatings Technology, vol. 382, Art. no. 124899, 2020. DOI: https://doi.org/10.1016/j.surfcoat.2019.124899
X. Jiang, A. V. Rogachev, and D. G. Piliptsou, “Effect of Cr layer on the structure and properties of Cr/DLC films,” Eurasian Chemico-Technological Journal, vol. 18, no. 4, pp. 275–281, 2016. DOI: https://doi.org/10.18321/ectj481
A. F. Yetim, H. Kovacı, A. E. Kasapoğlu, Y. B. Bozkurt, and A. Çelik, “Influences of Ti, Al and V metal doping on the structural, mechanical and tribological properties of DLC films,” Diamond and Related Materials, vol. 120, 2021. DOI: https://doi.org/10.1016/j.diamond.2021.108639
H. Cao, F. Qi, X. Ouyang, N. Zhao “Effect of Ti transition layer thickness on the structure, mechanical and adhesion properties of Ti-DLC coatings on aluminum alloys,” Materials, vol. 11, no. 9, p. 1742, 2018. DOI: https://doi.org/10.3390/ma11091742
D.-Y. Wang, “Process for depositing diamond-like carbon films by cathodic arc evaporation,” U.S. Patent 6,331,332 B1, Nov. 5, 1999
Y.-Y. Chang, D.-Y. Wang, and W. Wu, “Catalysis effect of metal doping on wear properties of diamond-like carbon films deposited by a cathodic-arc activated deposition process,” Thin Solid Films, vol. 420–421, pp. 241–247, 2002. DOI: https://doi.org/10.1016/S0040-6090(02)00801-5
A. Wasy, G. Balakrishnan, S. H. Lee, J. K. Kim, D. G. Kim, T. G. Kim, and J. I. Song, “Argon plasma treatment on metal substrates and effects on diamond-like carbon (DLC) coating properties,” Crystal Research and Technology, vol. 49, no. 1, pp. 55–62, 2014. DOI: https://doi.org/10.1002/crat.201300171
G. Pezzotti, C. Camara, E. Marin, W. Zhu, D. Green, A. Collins, and S. Putterman “Physical chemistry insights into surface charge phenomena during frictional coupling in triboelectric X-ray sources,” Journal of Materials Chemistry C, vol. 7, no. 25, pp. 7708–7724, 2019. DOI: https://doi.org/10.1039/C9TC02050K
N. Konkhunthot, P. Photongkam, and P. Wongpanya, “Improvement of thermal stability, adhesion strength and corrosion performance of diamond-like carbon films with titanium doping,” Applied Surface Science, vol. 469, pp. 471–486, Mar. 2019. DOI: https://doi.org/10.1016/j.apsusc.2018.11.028
A. C. Ferrari, and J. Robertson, “Interpretation of Raman spectra of disordered and amorphous carbon,” Physical Review B, vol. 61, no. 20, pp. 14095–14107, 2000. DOI: https://doi.org/10.1103/PhysRevB.61.14095
C. Li, L. Huang, and J. Yuan, “Effect of sp3 content on adhesion and tribological properties of non-hydrogenated DLC films,” Materials, vol. 13, no. 8, 2020. DOI: https://doi.org/10.3390/ma13081911
H. Sun, L. Yang, H. Wu, and L. Zhao, “Effects of Element doping on the structure and properties of diamond-like carbon films: A review,” Lubricants, vol. 11 no. 4, p. 186, 2023. DOI: https://doi.org/10.3390/lubricants11040186
S. Ghatrehsamani, and S. Akbarzadeh, “Predicting the wear coefficient and friction coefficient in dry point contact using continuum damage mechanics,” Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, vol. 233, no. 3, pp. 447–455, 2018. DOI: https://doi.org/10.1177/1350650118785045
M. Samiee, M. J. Eshraghi, and K. Asadian, “Tailoring the performance of DLC coatings through interlayer engineering,” Scientific Reports, vol. 15, no. 1, Art. no. 35663, 2025. DOI: https://doi.org/10.1038/s41598-025-19613-3
A. Choleridis, S. Sao-Joao, J. Ben-Mohamed, D. Chern, V. Barnier, G. Kermouche, C. Heau, M.-A. Leroy, J. Fontaine, S. Descartes, C. Donnet, and H. Klöcker, “Experimental study of wear-induced delamination for DLC coated automotive components,” Surface and Coatings Technology, vol. 352, pp. 549–560, 2018. DOI: https://doi.org/10.1016/j.surfcoat.2018.08.048
Downloads
Published
How to Cite
Issue
Section
Categories
License
Copyright (c) 2026 Journal of Metals, Materials and Minerals

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Authors who publish in this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.




