Microstructure based finite element simulation of JCO forming process for pipeline X65

Authors

  • Wut Thianngoen Faculty of Engineering, King Mongkut’s University Technology Thonburi
  • Saranya Kingklang Faculty of Engineering, King Mongkut’s University Technology Thonburi
  • Vitoon Uthaisangsuk Faculty of Engineering, King Mongkut’s University Technology Thonburi

Keywords:

X65 pipeline steel, Multi-scale modeling, RVE, FE simulation

Abstract

In recent years, strong increases in energy demand have become the most important issue in every section. High strength pipeline steels make large contribution to cost reduction for fuel transportation in oil and gas industries due to their great combination of optimal strength and toughness properties. Mechanical properties of pipeline steel tubes are significantly influenced by their microstructure characteristics, which in turn are controlled by the production. In this work, the JCO forming process of gas pipeline tube made of hot–rolled steel grade X65 with ferrite/pearlite microstructure was investigated by means of a FE multi–scale modeling approach. Three different scales including the nano–scale of a ferrite–cementite bi-lamella of pearlite, pearlite/ferrite microstructure on the micro–scale and macro–scale tube were considered. Firstly, local mechanical properties of the X65 steel were examined, in which steel specimens were heated up to austenitization temperature and cooled down to room temperature with high and low cooling rate. Obtained microstructures from both conditions represented material in the center and at the skin of the tube. Stress–strain responses of both different zones were determined by tensile test. Subsequently, FE representative volume element (RVE) models were generated taking into account existing phases and morphologies. Effective flow stress curve of pearlite was predicted by the nano–scale model. In the micro–scale RVE, pearlite with different morphologies distributed in a ferritic matrix was modeled. It was found that stress–strain curve of the X65 steel described by the micro–scale model agreed well with experimental flow curve. Then, two FE simulations of the JCO forming were carried out, by which one was defined with the same microstructure for all area of the tube and other incorporated different microstructures for the skin and center area of the tube. Obviously, the most critical stresses on the formed tube calculated by both models were deviated. Finally, RVE simulations were carried out for the skin and center area of the tube subjected to the JCO forming process. Stress and strain distribution in the microstructure of the X65 steel tube could be evaluated and discussed.

Downloads

Download data is not yet available.

Author Biographies

Wut Thianngoen, Faculty of Engineering, King Mongkut’s University Technology Thonburi

Department of Mechanical Engineering, Faculty of Engineering

Saranya Kingklang, Faculty of Engineering, King Mongkut’s University Technology Thonburi

Department of Mechanical Engineering, Faculty of Engineering

Vitoon Uthaisangsuk, Faculty of Engineering, King Mongkut’s University Technology Thonburi

Department of Mechanical Engineering, Faculty of Engineering

References

PTT Public Company Limited. (2555). Natural gas everyday. PTT Public Company Limited, Bangkok.

Wang, J. Q., Atrens, A., Cousens, D. R. and Kinaev, N. (1999). Microstructure of X52 and X65 pipeline steels. J. Mater. Sci. 34(8) : 1721-1728.

Allain, S. and Bouaziz, O. (2008). Microstructure based modeling for the mechanical behavior of ferrite-pearlite steels suitable to capture isotropic and kinematic hardening. Mater. Sci. Eng. A. : 496(1-2) : 329-336.

Laschet, G., Fayek, P., Henke, T., Quade, H. and Prahl, U. (2013). Derivation of anisotropic flow curves of ferrite–pearlite pipeline steel via a two–level homogenization scheme. Mater. Sci. Eng. A. 566 : 143-156.

Laschet, G., Shukla, M., Henke, T., Fayek, P., Bambach, M. and Prahl, U. (2014). Impact of the microstructure on the U-O forming simulations of a ferrite-pearlite pipeline tube. Steel Res. Int. 6 : 1083-1098.

Palumbo, G. and Tricarico, L. (2005). Effect of forming and calibration operations on the final shape of large diameter welded tubes. J. Mater. Proc. Technol. 164-165 : 1089-1098.

Ren, Q., Zon, T., Li, D., Tang, D. and Peng, Y. (2015). Numerical study on the X80 UOE pipe forming process. J. Mater. Proc. Technol. 215 : 264-277.

Liu, P. F., Zheng, J. Y., Zhang, B. J. and Shi, P. (2010). Failure analysis of natural gas buried X65 steel pipeline under deflection load using finite element method. Mater. Des. 31(3) : 1384-1391.

Gutierrez, I. and Altuna, M. A. (2008). Work-hardening of ferrite and microstructure-based modeling of its mechanical behavior under tension. Acta Materialia. 56 : 4682-4690.

Sirinakorn, T., Wongwises, S. and Uthaisangsuk, V. (2014). A study of local deformation and damage of dual phase steel. Mater. Des. 64 : 729-742.

Hagi, H. (1994). Effect of interface between cementite and ferrite on diffusion of hydrogen in carbon steel. Mater. Trans. JIM. 35(3) : 168-173.

Keller, C., Hug, E., Habraken, A. M. and Duchene, L. (2012). Finite element analysis of the free surface effects on the mechanical behaviour of thin nickel polycrystals. Int. J. Plasticity. 29 : 155-172.

Hangen, U. (2010). Mechanical properties of multi–phase materials. Hysitron Inc., USA.

Downloads

Published

2015-12-30

How to Cite

[1]
W. Thianngoen, S. Kingklang, and V. Uthaisangsuk, “Microstructure based finite element simulation of JCO forming process for pipeline X65”, J Met Mater Miner, vol. 25, no. 2, Dec. 2015.

Issue

Section

Original Research Articles