Investigation of deposition parameters on the structural properties and hardness of TiAlN films deposited via reactive pulsed DC magnetron sputteringInvestigation of deposition parameters on structural properties and hardness of TiAlN films deposited by reactive pulsed DC magnetron sputtering

Authors

  • Jariyaporn RUKKUN Department of Physics, Faculty of Science and Technology, Thammasat University, Prathumthani, 12121, Thailand
  • Kamon AIEMPANAKIT Department of Physics, Faculty of Science and Technology, Thammasat University, Prathumthani, 12121, Thailand
  • Pimchanok REAKAUKOT Department of Physics, Faculty of Science and Technology, Thammasat University, Prathumthani, 12121, Thailand
  • Witthawat WONGPISAN National Metal and Materials Technology Center (MTEC), National Science and Technology Department Agency (NSTDA), Prathumthani, 12120, Thailand
  • Kirati WAREE National Metal and Materials Technology Center (MTEC), National Science and Technology Department Agency (NSTDA), Prathumthani, 12120, Thailand
  • Montri AIEMPANAKIT Department of Physics, Faculty of Science, Silpakorn University, Nakhon Pathom, 73000, Thailand

DOI:

https://doi.org/10.55713/jmmm.v31i2.1083

Keywords:

Magnetron sputtering, TiAlN film, Nitrogen gas flow rate, Bias voltage

Abstract

In this work, titanium aluminum nitride (TiAlN) films were deposited on a silicon substrate via reactive pulsed DC magnetron sputtering. The effect of deposition parameters such as nitrogen gas flow rate, substrate temperature, and bias voltage on the structural and mechanical properties of TiAlN films was investigated. The crystal structure, morphology, and hardness of TiAlN films were characterized via X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM, and nanoindentation. An improved crystallinity of TiAlN films was obtained by varying the substrate temperature and bias voltage. The morphology of the TiAlN film exhibited a columnar structure, and the morphology gradually changed with the increase in bias voltage. The films thickness decreased upon increasing the nitrogen gas flow rate, substrate temperature, and bias voltage. In addition, the hardness of the TiAlN film was enhanced by adjusting the nitrogen gas flow rate, substrate temperature, and bias voltage, and a suitable elemental component ratio was obtained. A maximum hardness of approximately 28.9 GPa was obtained for the TiAlN film with a nitrogen gas flow rate of 4 sccm, substrate temperature of 500ºC, bias voltage of 100 V, and an elemental composition Al/(Al + Ti) of approximately 34.35%.

Downloads

Download data is not yet available.

References

J. Shi, C. M. Muders, A. Kumar, X. Jiang, Z. L. Pei, J. Gong, and C. Sun, “Study on nanocomposite Ti-Al-Si-Cu-N films with various Si contents deposited by cathodic vacuum arc ion plating,” Applied Surface Science, vol. 258, pp. 9642-9649, 2012.

F. Mei, N. Shao, L. Wei, and G. Li, “Effect of N2 partial pressure on the microstructure and mechanical properties of reactively sputtered (Ti,Al)N coatings,” Materials Letters, vol. 59, pp. 2210-2213, 2005.

G. Hakansson, J. E. Sundgren, D. McIntyre, J. E. Greene, and W. D. Munz, “Microstructure and physical properties of poly-crystalline metastable Ti0.5Al0.5N alloys grown by d.c. magnetron sputter deposition,” Thin Solid Films, vol. 153, pp. 55-65, 1987.

T. Gredic, and M. Zlatanovic, “Plasma deposition of (Ti,Al)N coatings at various magnetron discharge power levels,” Surface and Coatings Technology, vol. 48, pp. 25-30, 1991.

R. Jalali, M. Parhizkar, H. Bidadi, H. Naghshara, and S. Hosseini, “Effect of Al content, substrate temperature and nitrogen flow on the reactive magnetron co-sputtered nanostructure in TiAlN thin films intended for use as barrier material in DRAMs,” Journal of the Korean Physical Society, vol. 66, pp. 978-983, 2015.

F. Ali, B. S. Park, and J. S. Kwak, “The impact of surface morphology on TiAlN film’s properties,” Journal of Ceramic Processing Research, vol. 14, pp. 529-534, 2013.

X. Wang, K. Zhang, G. Yue, D. Peng, Z. Qi, and Z. Wang, “Investigation on the structure and properties of TiAlN coatings deposited by DC reactive magnetron sputtering,” Advanced Materials Research, vol. 154-155, pp. 1639-1642, 2011.

N. Ghobadi, M. Ganji, C. Luna, A. Arman, and A. Ahmadpourian, “Effects of substrate temperature on the properties of sputtered TiN thin films,” Journal of Materials Science: Materials in Electronics, vol. 27, pp. 2800-2808, 2016.

D. M. Devia, E. Restrepo-Parra, P. J. Arango, A. P. Tschiptschin, and J. M. Velez, “TiAlN coatings deposited by triode magnetron sputtering varying the bias voltage,” Applied Surface Science, vol. 257, pp. 6181-6185, 2011.

R. Wuhrer, and W. Y. Yeung, “A study on the microstructure and property development of d.c. magnetron cosputtered ternary titanium aluminium nitride coatings,” Journal of Materials Science, vol. 37, pp. 1993-2004, 2002.

L. Liua, L. Zhoub, W. Tang, Q. Ruan, X. Li, Z. Wu, A. M. Qasim, S. Cui, T. Li, X. Tian, R. K. Y. Fu, Z. Wu, and P. K. Chu, “Study of TiAlN coatings deposited by continuous high power magnetron sputtering (C-HPMS),” Surface and Coatings Technology, vol. 402, pp. 126315, 2020.

J. C. Oliveira, A. Manaia, J. P. Dias, A. Cavaleiro, D. Teer, and S. Taylor, “The structure and hardness of magnetron sputtered Ti-Al-N thin films with low N contents (42 at%),” Surface and Coatings Technology, vol. 200, pp. 6583-6587, 2006.

W. Tillmann, D. Grisales, D. Stangier, I. B. Jebara, and H. Kang, “Influence of the etching processes on the adhesion of TiAlN coatings deposited by DCMS, HiPIMS and hybrid techniques on heat treated AISI H11,” Surface and Coatings Technology, vol. 378, pp. 125075, 2019.

Downloads

Published

2021-06-27

How to Cite

[1]
J. RUKKUN, K. AIEMPANAKIT, P. REAKAUKOT, W. . WONGPISAN, K. WAREE, and M. AIEMPANAKIT, “Investigation of deposition parameters on the structural properties and hardness of TiAlN films deposited via reactive pulsed DC magnetron sputteringInvestigation of deposition parameters on structural properties and hardness of TiAlN films deposited by reactive pulsed DC magnetron sputtering”, J Met Mater Miner, vol. 31, no. 2, pp. 118–122, Jun. 2021.

Issue

Section

Original Research Articles

Most read articles by the same author(s)